![]() ![]() This error shows when the charger is configured to be controlled by a BMS, but does not receive any BMS control messages. For more information see the VictronConnect app chapter. Or, if the unit is connected to a GX device, the VictronConnect app can communicate via VRM. In case Bluetooth is not functional, turned off or unavailable, the VictronConnect app can still communicate via the unit’s VE.Direct port. Navigate to the device list of the VictronConnect app.Įnter the solar charger's unique PUK code as printed on its product information sticker.Ĭlick on the option symbol next to the solar charger listing.Ī new window will open which allows you to reset the PIN code back to its default: 000000. If you have lost the PIN code, you will need to reset the PIN code to its default PIN code. If still unresolved, refer to the VictronConnect app manual. Rule out any issues with the phone or the VictronConnect app by using another phone or tablet and try again. Try to connect to another Victron product, does this work? If that also does not work, there probably is an issue with the phone or tablet. Make sure no other devices are connected and try again. Only one phone or tablet can be connected to the solar charger at any given time. Press the orange refresh button at the bottom of the VictronConnect app device list and check if the solar charger is now listed. Some steps to try to resolve this issue are: ![]() The controller is missing in the VictronConnect app device list Or alternatively connect using a VE.Direct to USB interface. Use an Android, iOS or macOS device instead. The Windows version of the VictronConnect app does not support Bluetooth. The Windows VictronConnect app does not support Bluetooth In a build-up area, inside a house, a shed, a vehicle or a boat this distance can be a lot less. In open space the maximum Bluetooth distance is about 20 meters. Navigate to the controller settings and then to "product info".īluetooth is active as soon as the solar charger is powered-up. To re-enable:Ĭonnect to the solar charger via the VE.Direct port. It is possible to enable/disable Bluetooth in the product settings. If the system also contains a battery monitor, or if the system is connected to VRM, the battery voltages and the cycle history of the battery can be accessed This will give a complete picture of the battery history and it can be determined if the battery is near the end of its service life or has been abused. The solar charger will keep 30 day of battery voltage history. It is hard to tell what has exactly happened to a battery during its lifetime. It is not recommended to mix batteries of different ages in one battery bank. In case of multiple battery system replace the whole battery bank. When the faulty battery is charged, the damaged cell will not accept charge and the remaining cells will receive the broken cell’s charge voltage and thus will be overcharged. When a battery is old or has been damaged, a likely scenario is that one of these cells is not operational anymore. Err 203, Err 205, Err 212, Err 215 - Internal supply voltage errorĪ battery that is at the end of its service life or has been damaged by incorrect use, can be prone to being overcharged.Ī battery contains a number of cells that are connected in series. ![]() Error 55, Error 56, Error 58 - Inverter self test failed Error 53, Error 54 - Inverter output voltage Error 50, Error 52 - Inverter overload, Inverter peak current Error 43 - Inverter shutdown (Ground Fault) Error 42 - Inverter shutdown (Ground Fault) Error 41 - Inverter shutdown (PV isolation) Error 22, 23 - Internal temperature sensor failure Error 17 - Controller overheated despite reduced output current ![]() Error 8 - Remote battery voltage sense failure (connection lost) Error 6, Error 7 - Remote battery voltage sense failure Error 5 - Remote temperature sensor failure (connection lost) Error 3, Err 4 - Remote temperature sensor failure Appendix C : Example system schematic and wiring diagram MPPT grounding, detection of PV array insulation faults & Earth fault alarm notification ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |